Author Archives admin

HowTo: Hytera DMR Firmware upgrade

21 augustus 2017
/ /
in Blog
/
Comments Closed

Hytera MD785 Mobile (Normal USB-Cable)

  1. Simultaneously hold Microphone hanger against a metal part of the transceiver case and push PTT, and power on the transceiver.
  2. Release PTT.
  3. The big knob lights red.
  4. Disconnect the microphone and connect the USB-cable.
  5. Run the upgrade software.
  6. Connect the transceiver to PC.
  7. Click “UPGRADE”. The software will do the rest.
  8. After the upgrade has finished, power off the device and disconnect.

Hytera MD785 Mobile  (USB-Cable with switch)

  1. Check the two-position switch on the USB-cable.
  2. Set the switch to “DL” for software-upgrade.
  3. Run the upgrade software.
  4. Connect the device.
  5. Power on the device.
  6. Click UPGRADE. The software will do the rest.
  7. After the upgrade has finished, power off the device and disconnect.

Hytera MD655 Mobile (USB-Cable with switch)

  1. Check the two-position switch on the USB-cable.
  2. Set the switch to “DL” for software-upgrade.
  3. Run the upgrade software.
  4. Connect the device.
  5. Power on the device.
  6. Click UPGRADE. The software will do the rest.
  7. After the upgrade has finished, power off the device and disconnect.

Hytera PD785, PD985 portables

  1. Connect the USB-cable to the transceiver.
  2. Press PTT, TK (orange knob on top) simultaneously and power on the device.
  3. Run the upgrade software.
  4. Connect the device to PC.
  5. Click UPGRADE. The software will do the rest.
  6. After the upgrade has finished, power off the device and disconnect.

Hytera X1P portable

  1. Check the two-position switch on the USB-cable.
  2. Set the switch to “DL” for software-upgrade.
  3. Run the upgrade software.
  4. Connect the device.
  5. Power on the device.
  6. Click UPGRADE. The software will do the rest.
  7. After the upgrade has finished, power off the device and disconnect.

Hytera PD365 portable

  1. Power off the Subscriber and take off the battery.
  2. Connect the subscriber to PC by USB-cable.
  3. Push and hold the small button (SK1) below the PTT during the next few steps.
  4. Re-install the battery.
  5. Wait for 3-5 seconds.
  6. Release SK1 so as to enter the upgrade mode.
  7. Run the software, select the correct ComPort, should you not find the correct ComPort, click on the REFRESH-button.
  8. Click “UPGRADE” in the main interface to start the upgrade-process. The software will do the rest. The information on the progress-bar will show: “Updating, please wait….”. After more or less 5 seconds, the information on the progress-bar will display the % rate of the forth going upgrade-process. The upgrade-process will take more or less 1 minute to finish. Finally, the information-bar will prompt “Upgrade completed successfully”.
  9. Click OK and power-off the subscriber.
Read More

SafeSignal is Hytera Partner in de Benelux

2 januari 2016
/ / /
Comments Closed

Vanaf 2016 is SafeSignal een Hytera Partner voor al onze klanten in de Benelux. Dit betekent dat we het gehele Hytera gamma van analoge en digitale radiocommunicatie en bijbehorende accessoires aanbieden en ondersteuning leveren. Aanbod Naast licentievrije analoge oplossingen voor kleine bedrijven en locaties, bieden wij ook het gamma analoge licentieplichtige radio’s aan. Wij kunnen […]

Read More

Nieuwe website

2 januari 2016
/ / /
Comments Closed

Onze website kreeg recent een opfrissing, en de komende maanden wordt de functionaliteit uitgebreid.

Verbeteringen

Door de opfrissing is onze website beter leesbaar op mobiele telefoons en tablets, wat het voor u makkelijker maakt om onze informatie terug te vinden. De komende maanden werken we verder aan het leveren van meer informatie via onze website. We voorzien ook een stevige verbetering van onze webshop, waarmee u sneller en eenvoudiger een bestelling kan plaatsen, of een offerte kan genereren.

Via ons contactformulier is het vanzelfsprekend nog altijd mogelijk om een op maat gemaakte offerte aan te vragen.

Read More